Shandong Hongda Tower Crane with 30m
1.Use qualified 16Mn and Q235B steel from domestic famous manufacturers, such as Bao steel.
2. Painting Process. After shot-blast cleaning, spraying anti-rust paint, then spray paint.
3.Use high-strength wire in the welding process. Main joints use special steel and special process.
4. Electric devices are from international well-known manufacturers, such as Schneider, Omron.
5. Motor and deceleration devices use domestic famous manufacturers' products, eg: Shanghai, Jiangxi Special Electric Motor Co., Ltd.,Tianjin etc, to ensure the long life.
6.Each device is in strict test, then can packed to ship, to ensure that the trouble after leave the factory reduced to the minimum.
7.The only tower crane institute of Shandong Province located in HONGDA Group, which has more than 50 engineers designing products.
Working grades for mechanism |
Hoisting mechanism | M5 | |||||||||||||
Slewing mechanism | M4 | ||||||||||||||
Trolley travelling mechanism | M4 | ||||||||||||||
Hoisting height (m) |
Multiplying |
Independent |
Undercarriage |
Attached |
|||||||||||
a=2 | 34 | 34 | 139 | ||||||||||||
a=4 | 34 | 34 | 69 | ||||||||||||
(t) Max. hoisting capacity (t) |
5 | ||||||||||||||
Radius (m) | Max. radius | 50 | |||||||||||||
Min. radius | 2.0 | ||||||||||||||
Hoisting mechanism |
Multiplying |
a=2 | a=4 | ||||||||||||
(t) Hoisting capacity(t) |
1.25 | 2.5 | 2.5 | 2.5 | 5 | 5 | |||||||||
(m/min) Speed (m/min) |
58 | 29 | 8 | 29 | 14.5 | 4 | |||||||||
(KW) Power (kW) | 15/15/4 | ||||||||||||||
Trolley travelling mechanism |
(m/min) Speed (m/min) |
40/20 | |||||||||||||
(kw) Power (kW) |
2.4/1.5 | ||||||||||||||
Slewing mechanism |
(r/min) Speed (r/min) |
0-0.62 | |||||||||||||
Monment motor | Torque (Nm) |
85 | |||||||||||||
Round-line motor |
Power (KW) |
5.5 | |||||||||||||
, Traveling mechanism |
(m/min) Speed(m/min) |
0~25 | |||||||||||||
(kw) Power (kw) |
2×5.2 | ||||||||||||||
Climbing mechanism |
(m/min) Speed (m/min) |
0.5 | |||||||||||||
(kw) Power (kW) |
4 | ||||||||||||||
(Mpa) Rated working pressure for hydraulic system (Mpa) |
20 | ||||||||||||||
Counter-weight |
Jib length(m) |
50 | 44 | 38 | 32 | ||||||||||
(t) Counter-weight |
10.01 | 8.58 | 7.15 | 5.72 | |||||||||||
(KW) Total power(KW) |
33.3 | ||||||||||||||
×(m) Wheel×axle gauge(m) |
3.9×3.9 | ||||||||||||||
(ºC) Operating temperature(ºC) |
-20~+40 |
1.Use qualified 16Mn and Q235B steel from domestic famous manufacturers, such as Bao steel.
2. Painting Process. After shot-blast cleaning, spraying anti-rust paint, then spray paint.
3.Use high-strength wire in the welding process. Main joints use special steel and special process.
4. Electric devices are from international well-known manufacturers, such as Schneider, Omron.
5. Motor and deceleration devices use domestic famous manufacturers' products, eg: Shanghai, Jiangxi Special Electric Motor Co., Ltd.,Tianjin etc, to ensure the long life.
6.Each device is in strict test, then can packed to ship, to ensure that the trouble after leave the factory reduced to the minimum.
7.The only tower crane institute of Shandong Province located in HONGDA Group, which has more than 50 engineers designing products.